Welcome to Chipmall.com
Products
View All Products
Home > News > News detail

4558d How to measure the quality of each foot

elecfans | 08/05/2021

Introduction to 4558D

4558 is a low-noise dual operational amplifier integrated circuit, which is most suitable for active filters, compensation amplifiers, audio preamplifiers, equalizer amplifiers, and amplifiers for various circuits in electronic instruments and meters.

4558D pin diagram and function

1: AMP OUT1 amplified signal output (1)

2: IN1- reverse signal input (1)

3: IN1+ non-phase signal input (1)

4: GND ground

5: IN2+ non-phase signal input (2)

6: IN2-Inverted lotus root climbing? 2)

7: AMP OUT2 amplified signal output (2)

8: Vcc power supply

The rated voltage is 9v

4558D each pin voltage

The voltage varies according to its application circuit. It is usually powered by a dual power supply to the ground, and sometimes it can be powered by a single power supply.

is used in audio circuits, sometimes it is used for multiple amplification, sometimes it is connected as a follower without multiple amplification, sometimes it is in-phase amplification, and sometimes it is inverted amplification. Pin 8 is positive, pin 4 is negative, pin 1 and pin 7 output zero volts, pin 3 and pin 5 are in-phase input, pin 2 and pin 6 are inverting input, which are usually lower than half of the supply voltage depending on the circuit design.

4558D circuit diagram

4558d How to measure the quality of each foot

How to measure the quality of the JRC4558D op amp used on the power amplifier? Follow below to find out:

Generally speaking, when the op amp is working in a dual power supply circuit, the resistance of the V+V- power supply terminal to ground cannot be zero, and the resistance of other pins that are not directly grounded cannot be zero (refer to the circuit diagram); pin 8 is a positive power supply, Pin 4 is a negative power supply, and the voltage to ground should be ±12V.

In addition, if it is a multi-channel microphone input, it can be inspected in a targeted manner. You can use the induction signal injection method to check whether the circuit is damaged. If the speaker has a loud hum when touching pins 3 and 5 with a screwdriver, the op amp is good. Otherwise, it may be damaged; when there is no signal, the voltage of pins 1 and 7 to ground should be 0V. If the deviation is large, it can be judged that the op amp is damaged.

Extended reading: What is a dual operational amplifier

The dual operational amplifier is the integration of two general operational amplifiers on a single chip. It has the characteristics of high gain, high common mode rejection ratio, wide common mode range, simple compensation, stable operation, and good temperature stability between the two operational amplifiers.

The two ops are placed in their respective input, output, power supply and correction capacitor terminals, which is easy to use. It can be widely used in a variety of analog arithmetic units, active filters, waveform generators, data amplifiers and other occasions where a large number of operational amplifiers are used.

Features

1. High common mode rejection ratio, wide common mode input range

2. Simple compensation and stable work

Tags

4558d

Topic
News Homepage
News detail

Brands

Cross News

1. 4558d How to measure the quality of each foot

4558d How to measure the quality of each foot

2. Modular power supplies offer up to 18 outputs with...

Modular power supplies offer up to 18 outputs with low acoustic noise and full MoPPs isolation

3. Smart storage includes an open-source toolkit for ...

Smart storage includes an open-source toolkit for managing data centre storage

4. Power MOSFETs offer high power density and efficiency

Power MOSFETs offer high power density and efficiency

5. Sensor modules provide long range presence and pro...

Sensor modules provide long range presence and proximity sensing for light curtain applications

6. AMD Achieves 25x Energy Efficiency Goal from 2014

AMD Achieves 25x Energy Efficiency Goal from 2014

7. Podcast: DAC 2020 preview – AI, ML and RISC-V on rise

Podcast: DAC 2020 preview – AI, ML and RISC-V on rise

8. New touchscreen controller for smart surfaces and ...

New touchscreen controller for smart surfaces and multi-function displays

9. Intel to Introduce Control-Flow Enforcement Techno...

Intel to Introduce Control-Flow Enforcement Technology into Tiger Lake Mobile CPUs

10. What do AI users predict for its future?

What do AI users predict for its future?

Connect with us
Email error
©2022 Chipmall Electronics Limited. All Rights Reserved.    Sitemap
We use cookies to offer you a better experience. Detailed information on the use of cookies on this website is provided in our Privacy Policy. By using this site, you consent to the use of our cookies.
Accept